Drainage, storm water and ground materials for building, infrastructure and landscape programmes, supplied from Dubai and quoted line by line from your bill of quantities.
The range follows the water: floor and roof drains in the building, grease and oil separation, surface channels, below-ground storage, and the outfall valve and cover at the far end. Landscape layers complete the scope for planted decks, ponds and podiums.
Each section gives the product type, the standard it is designed to, where it is used and what we need from you to price it.
Polymer concrete channels, slot drains and a heavy-duty slot drain, with gratings in ductile iron, galvanised steel or stainless steel.
Tanks, chambers, separators and valves for the path of storm water, from the tank to the outfall.
Recessed and solid covers in stainless steel, galvanised steel and aluminium, up to load class F900, single or multi-part. FRP covers are also supplied, for locations that need a cover that is light, resists corrosion and does not conduct electricity.
Drainage cell, root guard and salt barrier, and EPDM liners for ponds, reservoirs and water features.
Also supplied: corrugated and perforated drainage pipe, low-noise drainage pipe systems, lifting stations, balcony, area and planter drains, geotextiles and geogrids.
Load class and standard are the first two lines of any drainage specification.
| Class | Test load | Where it is used |
|---|---|---|
| A15 | 15 kN | Pedestrian and cycle areas only. |
| B125 | 125 kN | Footways, pedestrian zones, private car parks and parking decks. |
| C250 | 250 kN | Kerbside channels at the edge of roads. |
| D400 | 400 kN | Carriageways and pedestrian streets, hard shoulders and parking areas for all vehicles. |
| E600 | 600 kN | High wheel loads, such as docks. |
| F900 | 900 kN | Particularly high wheel loads, such as aircraft pavements. |
Load classes apply to channels and gratings (EN 1433) and to gully and manhole tops (EN 124).
| Standard | Covers | Used for |
|---|---|---|
| EN 1433 | Drainage channels for vehicular and pedestrian areas: classification, design and testing requirements, marking and evaluation of conformity. | Channel drains, slot drains |
| EN 124 | Gully tops and manhole tops for vehicular and pedestrian areas, in parts by material: classification, design, testing. | Access covers, gully tops |
| EN 858-1 | Separator systems for light liquids, such as oil and petrol: principles of product design, performance and testing, marking and quality control. | Oil separators |
| EN 1825-1 | Grease separators: principles of design, performance and testing, marking and quality control. | Grease separators |
Class belongs to the installed system. The class applies to the channel, its grating and the installation together. Each must meet the class required for the traffic above it, and the installation must follow the instructions supplied with the product.
Oil separator classes. Class I separators discharge not more than 5 mg of residual oil per litre under test conditions. Class II separators discharge not more than 100 mg per litre. Where a project works to another standard, state it in the enquiry.
A bill of quantities, a drawing set or a product list is enough to start. The quotation comes back line by line.
Specifications in the brochure are typical and are confirmed against the data sheet of the product supplied. Load class, standard and dimensions are stated in the quotation for each line.
Length, load class, channel width and depth, grating type and material, outlets and end caps.
Storage volume, depth of cover, traffic load, groundwater level, attenuation or infiltration.
Design flow in l/s, Class I or II, full retention or bypass, alarm, installation depth and groundwater level.
Nominal size or flow rate, free-standing or below ground, manual or automatic disposal.
Outlet size and type, body material, strainer, roof area or flow, floor build-up.
Pipe or opening diameter, outfall type, fresh, storm or tidal water, headwall details.
Clear opening, load class, material, depth of recessed finish, single or multi-part.
Area in m2, application, thickness or type, drainage fall.
16 pages, in English, as a PDF.
Give us your first name, second name and email address and we email you a personal link.
Yes. A bill of quantities, a drawing set or a product list is enough to start. The quotation comes back line by line, each product described to its standard and load class, with its lead time.
The class follows the traffic above it: A15 for pedestrian and cycle areas, B125 for footways and private car parks, C250 for kerbside channels, D400 for carriageways and parking areas for all vehicles, E600 for high wheel loads such as docks, and F900 for aircraft pavements. The class applies to the channel, its grating and the installation together.
Under test conditions a Class I separator discharges not more than 5 mg of residual oil per litre, and a Class II separator not more than 100 mg per litre (EN 858-1).
Data sheets, test and conformity reports and installation instructions for the destination market.
The minimum order value is USD 3,000.
Send drawings, a bill of quantities or a product list.
Send an enquiry